OMS Combi

OMS Combi Support
What can I do if I lose the code?

The combination lock 8002 can be opened with the master key whenever the entered code is forgotten or lost or in an emergency. In addition, the use of the master key to open the lock will make it possible to find out the code used. Steps to follow: 

  1. Opening the door with a master key:
    Open the door with the master key.
  2. Code retrieval:
    With the door open and access to the back of the lock, the combination stored in the lock can be retrieved as follows: Firmly press and hold the code retrieval lever inside the lock. While holding down the lever, turn each code wheel clockwise until it stops, or a click is heard

3. Confirmation of the code:
The numbers on which the wheels stop will form the code stored in the lock, so you should now be able to open and close the lock normally. If the lock does not open and close normally, repeat step 2. Code retrieval.

The lock has two operating modes:

    1. Fixed mode (F): In this mode, the code is fixed, and the same code is always used to open the lock.
    2. Free mode (R): The locker user can reset the locking code in this mode. When leaving the locker, the next user can set their own code. Note: The lock is supplied from the factory in free mode.
  1. With the lock in the locked position, ensure that the adjusting screw on the back of the lock is turned to position R.

2. Using the turn knob, turn the lock to the open position, with the blue arrow pointing vertically.

  1. Now enter the fixed 4-digit code by turning the wheels.
  2. Turn the knob 90° to the left or right to the locked position depending on the orientation of your lock.

5. Now turn the adjusting screw on the back of the lock to position F. From now on, the lock will be used in fixed mode, and the same code must always be used to open the lock.

**Important: After step 4, the user must turn the code wheels randomly for both free and fixed mode. This will prevent other users from being able to see your lock code.

  1. With the lock in the locked position, ensure that the mode adjustment screw on the back of the lock is turned to position R.

2. Use the knob to turn the lock to the open position.

  1. With the lock still in the open position, turn the wheels to indicate the required 4-digit code.
  2. Close the door and turn the lock to the locked position according to the orientation of your lock.

**Important: After step 4, the user must turn the code wheels randomly for both free and fixed mode. This will prevent other users from being able to see your lock code.

OMS Combi assembly instructions

QUERIES / INCIDENTS

We respond to your Query / Incident.

TECHNICAL ASSISTANCE

Request online or on-site assistance from our technicians.

REPAIRS AND PHYSICAL DAMAGE

Repair services for out-of-warranty products.

QUERIES / INCIDENTS

Once we receive your query / incident, one of our technicians will contact you.

    *Mandatory fields


    Ojmar S.A., as data controller, informs you that your data are collected for the purpose of: Management of sending communications about our services The legal basis for the treatment is the consent of the person concerned.
    Your data will not be transferred to third parties unless legally required. Any person has the right to request access, rectification, deletion, limitation of processing, opposition or right to portability of your personal
    data, by writing to us at our office address, or by sending an email to lockerlocks@ojmar.com, indicating the right you wish to exercise. You can obtain additional information on our website: ojmar.com

    TECHNICAL ASSISTANCE

    Request online or on-site assistance from our technicians.

    One of our advisers will contact you after receiving the request via Ojmar.
    After Sales Service, to provide you with the information and prepare an estimate.

      *Mandatory fields


      Ojmar S.A., as data controller, informs you that your data are collected for the purpose of: Management of sending communications about our services The legal basis for the treatment is the consent of the person concerned.
      Your data will not be transferred to third parties unless legally required. Any person has the right to request access, rectification, deletion, limitation of processing, opposition or right to portability of your personal
      data, by writing to us at our office address, or by sending an email to lockerlocks@ojmar.com, indicating the right you wish to exercise. You can obtain additional information on our website: ojmar.com

      REPAIRS AND PHYSICAL DAMAGE

      Repair services for out-of-warranty products

      • * To guarantee the correct functioning of Ojmar locks and extend their useful life, we offer a repair service.
      • * This service has a minimum cost of €65.
      • * Before filling in the ADM, make sure that the FREQUENTLY ASKED QUESTIONS do not solve your issue.

      SERVICE CONDITIONS

      ADM (MATERIAL RETURN AUTHORISATION) FORM

      Read carefully the following points before filling in the form:

      1. Warranty
      We grant the specific product warranty to OJMAR S.A. products, according to our General Sales Conditions. This warranty is a warranty with delivery at the point of service, and does not include any provision for on-site services.
      The warranty does not include wear and tear parts. Also excluded from the warranty are all faults caused by damages from transportation, mishandling, unqualified repair attempts, mechanical damage, and the use of unsuitable consumables. Warranty rights do not include either faults that have been caused by installation errors and incorrect handling by the Customer. For everything else, expressly refer to the General Terms and Conditions of OJMAR, S.A.
      The warranty of the repairs will be valid for 6 months.
      For repairs carried out in the 2-year guarantee period, the latter will finish in any case when this period has ended.

      2. In case of repair out of warranty, a repair offer will be sent.
      This Service will only be valid forElectronic Solutions.
      The offer will include a minimum cost of 65€ in concept of “Cost of Handling, Analysis and Repair Management”. Once the validity period of the offer has elapsed, without a response from the client, OJMAR, S.A. reserves the right to choose between scraping the material or return it without repair, “carriage due”.

      3. Returned material must be accompanied by the ADM form.
      In the case of material returned without the ADM form, OJMAR, S.A. reserves the right to return it to the sender “carriage due”.

      4. Returned material must be sent properly packed.
      If the packaging is not correct, the warranty rights are endangered. Resulting damage during transportation means the cancellation of all warranty rights.

      5. Transportation costs
      OJMAR, S.A. assumes the cost of transport (both collection and return in case of product under warranty). In the event of repairs out of warranty, customer will send the material to be repaired to OJMAR, S.A facilities (adress below) and will assume all costs for both delivery and return of the repaired material (in DDP Elgoibar conditions).

      OJMAR, S.A
      P.I. Lerún S/N
      20870 ELGOIBAR – SPAIN

      Attn. Quality Department

      6. Description of the error.
      The ADM form must include a detailed description of the error (“faulty” or “for repair” is insufficient). In case of an insufficient description, OJMAR, S.A. reserves the right to verify (billing the cost of the service) or to return the material unchecked “carriage due”.

      7. Improper claims
      In case of improper claims (no errors are detected, manipulations, incorrect assembly or initialization…) the cost of the checking and processing service will be charged. The material will be sent “carriage due”.

      8. Terms of Delivery and Service
      The delivery and payment conditions of OJMAR, S.A. apply without any change.


        *Mandatory fields


        Ojmar S.A., as data controller, informs you that your data are collected for the purpose of: Management of sending communications about our services The legal basis for the treatment is the consent of the person concerned.
        Your data will not be transferred to third parties unless legally required. Any person has the right to request access, rectification, deletion, limitation of processing, opposition or right to portability of your personal
        data, by writing to us at our office address, or by sending an email to lockerlocks@ojmar.com, indicating the right you wish to exercise. You can obtain additional information on our website: ojmar.com

        How can we help your business?

        Contact us today